Membership

Select a plan to access over 65 CCNA 200-125 Labs

Register and Login at eConfigs.com before ordering to avoid any delays

CCNA 200-125 Labs

• CCNA 1.1: Compare and contrast OSI and TCP/IP models (FREE LAB!)
• CCNA 1.2: Compare and contrast TCP and UDP protocols
• CCNA 1.7: Select the appropriate cabling type based on implementation requirements
• CCNA 1.9: Configure, verify and troubleshoot IPv4 addressing and subnetting
• CCNA-1.11: Describe the need for private IPv4 addressing
• CCNA-1.12: Identify the appropriate IPv6 addressing scheme to satisfy addressing requirements in a LAN/WAN environment
• CCNA 1.13: Configure, verify and troubleshoot IPv6 addressing
• CCNA 1.14: Configure and verify IPv6 Stateless Address Auto Configuration
• CCNA 2.4: Configure, verify, and troubleshoot VLANs (normal/extended range) spanning multiple switches
• CCNA 2.4.a: Access ports (data and voice) (FREE LAB!)
• CCNA 2.4.b: Default vlan
• CCNA 2.5.a: Trunk ports
• CCNA 2.5.b: Add and remove VLANs on a trunk
• CCNA 2.5.c: DTP – Dynamic Trunking Protocol (DTP)
• CCNA 2.5.d: VTP (v1&v2) – VLAN Trunking Protocol
• CCNA 2.5.e: 802.1Q
• CCNA 2.5.f: Native VLAN
• CCNA 2.6.a: STP mode (PVST+ and RPVST+)
• CCNA 2.7.a: PortFast
• CCNA 2.7.b: BPDU Guard
• CCNA 2.8.a: Cisco Discovery Protocol (CDP)
• CCNA 2.8.b: Link Layer Discovery Protocol (LLDP)
• CCNA 2.9.a: Static PortChannel
• CCNA 2.9.b: Port Aggregation Protocol (PaGP)
• CCNA 2.9.c: Link Aggregation Protocol (LACP)
• CCNA 3.1.a: Packet handling along the path through a network (FREE LAB!)
• CCNA 3.1.c: Frame Rewrite
• CCNA 3.4.a: Router on a Stick
• CCNA 3.4.b: Switch Virtual Interface (SVI)
• CCNA 3.8.a: Default route
• CCNA 3.8.b: Network route
• CCNA 3.8.c: Host Route
• CCNA 3.8.d: Floating Static Route
• CCNA 3.9: Configure, verify, and troubleshoot single area and multi-area OSPFv2 for IPv4
• CCNA 3.10: Configure, verify, and troubleshoot single area and multi-area OSPFv3 for IPv6
• CCNA 3.11: Configure, verify and troubleshoot EIGRP for IPv4
• CCNA 3.12: Configure, verify and troubleshoot EIGRP for IPv6
• CCNA 3.13: Configure, verify, and troubleshoot RIPv2 for IPv4
• CCNA 4.1: Configure and verify PPP and MLPPP on WAN interfaces using local authentication
• CCNA 4.2: Configure, verify, and troubleshoot PPPoE client-side interfaces using local authentication
• CCNA 4.3: Configure, verify and troubleshoot GRE tunnel connectivity (FREE LAB!)
• CCNA 4.6: Configure and verify single-homed branch connectivity using eBGP IPv4
• CCNA 5.1: Describe DNS lookup operation
• CCNA 5.3.a: Configure and verify DHCP on a router – Server
• CCNA 5.3.b: Configure and verify DHCP on a router – Relay
• CCNA 5.3.c: Configure and verify DHCP on a router – Client
• CCNA 5.3.d: Configure and verify DHCP on a router – TFTP, DNS and gateway options
• CCNA 5.3: Configure and verify DHCP on a router
• CCNA 5.4: Troubleshoot client- and router-based DHCP connectivity issues
• CCNA 5.5: Configure, verify, and troubleshoot basic HSRP
• CCNA 5.6: Configure, verify, and troubleshoot inside source NAT
• CCNA 5.7: Configure and verify NTP operating in a client/server mode
• CCNA 6.1: Configure, verify, and troubleshoot port security
• CCNA 6.3: Configure, verify, and troubleshoot IPv4 and IPv6 access list for traffic filtering
• CCNA 6.5: Configure, verify, and troubleshoot basic device hardening
• CCNA 7.1.a: SNMPv2
• CCNA 7.1.c: Syslog
• CCNA 7.3.a: Backup and restore device configuration
• CCNA 7.3.b: Using Cisco Discovery Protocol or LLDP for device discovery
• CCNA 7.3.d: Logging
• CCNA 7.3.e: Timezone
• CCNA 7.3.f: Loopback
• CCNA 7.4: Configure and verify initial device configuration
• CCNA 7.5.a: Cisco IOS upgrades and recovery (SCP, FTP, TFTP, and MD5 verify)
• CCNA 7.5.b: Password recovery and configuration register